Scrap Processing Machine

[copperkid_18]

Hi, Im new and have access to lots of circuit boards. I was wondering how to get the gold off and out of them. I don't know if you need a machine or chemicals or what. ANYTHING! Thanks, Kobe :mrgreen:

 

[jimdoc]

Kobe,
You have been a member less than an hour. You have a lot of reading ahead of you. You will find the answers to your question and much more by reading the forum. You may find it easier to just sell them.
You have some homework ahead, help will be here if you need it, but please read and search the forum a bit first.
Jim

 

[copperkid_18]

Kobe,
You have been a member less than an hour. You have a lot of reading ahead of you. You will find the answers to your question and much more by reading the forum. You may find it easier to just sell them.
You have some homework ahead, help will be here if you need it, but please read and search the forum a bit first.
Jim

I have researched this stuff quite a bit in the past, and was wondering if there was a simple was to remove gold plating, Though thanks, Kobe

 

[jimdoc]

Watch Lazer Steve's videos on his website;
http://www.goldrecovery.us/

Also Palladium has the forum handbooks to download in his signature section of his member page;
http://goldrefiningforum.com/phpBB3/memberlist.php?mode=viewprofile&u=1666

Gold fingers are easy, pins are a little harder. Whole boards I just sell.

Jim

 

[pinwheel]

How much is a lot?

I will buy them if you have tonnage.

 

[copperkid_18]

How much is a lot?

I will buy them if you have tonnage.

Oh, About a 100 lbs, or so. Can probably get access to lots more. Kobe

 

[leavemealone]

I have researched this stuff quite a bit in the past, and was wondering if there was a simple was to remove gold plating,

If you've researched this quite a bit,and still have to ask then I would just consider selling it if I were you.
Johnny

 

[copperkid_18]

I have researched this stuff quite a bit in the past, and was wondering if there was a simple was to remove gold plating,

If you've researched this quite a bit,and still have to ask then I would just consider selling it if I were you.
Johnny

Well what it comes down to is that I was Simply asking if there was an easy to use machine out there, Kobe

 

[jimdoc]

I would say no to the easy machine question.

Jim

 

[copperkid_18]

I would say no to the easy machine question.

Jim

Is there any machine?

 

[jimdoc]

A machine to do what? Put boards in and get gold out?

 

[leavemealone]

Seriously copperkid.......no offense,but if there were some "easy" machine out there none of us would be here.
Johnny

 

[copperkid_18]

A machine to do what? Put boards in and get gold out?

You got it!

 

[copperkid_18]

Seriously copperkid.......no offense,but if there were some "easy" machine out there none of us would be here.
Johnny

Ok, sorry for taking any of your time.

 

[jimdoc]

A machine to do what? Put boards in and get gold out?

You got it!

If you find one, save your money, because it will be a scam.

 

[copperkid_18]

A machine to do what? Put boards in and get gold out?

You got it!

If you find one, save your money, because it will be a scam.

Ok, thanks! I bid on one on ebay up to $100 and good thing I lost. It was a reverselectroplator.

 

[jimdoc]

Check the videos I told you about on Lazer Steve's site.
They should help you.

Jim

 

[copperkid_18]

Check the videos I told you about on Lazer Steve's site.
They should help you.

Jim

I got on the website, but could not find them, Kobe

 

[jimdoc]

Under the red lettering there is a yellow section with a list of the video categories. Click show, and it will show the separate videos.
Check the Cell Videos.

Jim

 

[shadybear]

I have never used a cell but from reading here on the forum and LaserSteve's site you will be able to make your own for far less then several hundred dollars for a plastic bucket and a couple of stainless steel plates,Read,Read, Read.
You will here this many times.
Everything you need to know is here!