Ok so I ran a few batches of gold filled, burned and processed my filters I have built up and processed nitric waste i been pouring over some gold colored chalices mark international silver co. in a collection pot and processed the other stock pots for any waste. Did several nitric dissolutions on all that for a single AR. I didn't get any silver out from the nitric solution even after a day of leaving copper in to cement. So ok I took all the filtration from the batches and filters and incinerated then into AR. Filtered solution added ice and sodium metabisulfite to percipitate the gold. I knew some gold was in solution from a stannous test. After a few hours or so I looked at it and these crystal formation are dropping out. (See photo) does anyone know what is dropping out so I know what to do with it? I.e. run thru nitric again to seperate and then thru AR to get gold out. Or if this is something other then silver or gold. I wouldn't think it's silver cause silver would have come out at the nitric phase of dissolution. I've just never had this reaction with metabisulfite to percipitate gold before.
Has any seen this type of percipitate from AR before?
- Thread starter Emryst
- Start date
Help Support Gold Refining Forum:
I'm on a phone so it is not too easy to reply properly.
But it seems you plan changes many times and often without sufficient reasoning.
A weak Stannous might not even be visible as it cements.
And you spend way to much Nitric.
Ice is added before filtering not along the SMB.
I don't know what u mean my plan change many times. I had alot of stuff gold filled jewelry, stock pots, filters and the pouring off pot to refine. Rather then do one each time with small or no gold values in each I held and combined for a single AR solution. For me to be able to do all the different sources i.e gold filled filters stock pots collections. I would have needed a 5 gallon beaker or some thing.
I don't know if this clarified why i did what a did and how i did it and i dont think the ice being added before or after filtering would matter much on getting this result in the AR percipitatant but i will add before filtering in future refinings. Tho you didn't even answer what this percipitatant might be given your greater experience in refining.
I haven't gotten a close look at it as it had not been enough time for the percipition to finish i will see that in a few hours when I can get back to it.
The problem you are encountering is due to the fact you combined different material sources hoping to save time and or chemicals, we always advise to process each type of material separately for this very reason .
My advice add copper to your solution and try to recover the values that way .
My advice add copper to your solution and try to recover the values that way .
If anyone is following this thread and has any ideas. I finally got back to pour off the solution to see what percipitated out and here it is some kind of ugly looking shag rug lol. I have never seen this before. But my experience is far from vast with home refining. And I have no chemistry back ground to speak of as well. So any ideas would be much appreciated on what this is and how to proceed. Cause my only thought is to do another hot nitric on it and then back in AR after. It's really my only 2 weapons in my arsenal. Lol the last photo I think shows the gold that percipitated out first.
Attachments
Ok so if you could look at my last post to this thread and advice a course of action. I.e. hot nitric then AR again. I believe i can see my values on the bottom. I just don't know what the grey silverfish stuff is and how to seperate them. To my understanding platinum is not dissolved in nitric but does in AR. I use smb to percipitate and I may be wrong but I thought smb didn't target platnium to percipitate only gold. So I can't figure out what dropped out with gold in this crystal formation.
You are near the end of your process,
Think things through
Let's see a picture of your test for gold after your SMB drop
Think things through
Let's see a picture of your test for gold after your SMB drop
I think it is a copper compound that is formed by excess metabisulfite. It has happened to me that when I have melted it, instead of pure refined gold appearing, copper also appears. but it can be melted without problem. I would wash it well with water and filter, and then melt. you will get gold with copper and other metals, so you will have to refine it again
Martijn
Well-known member
Melting gold to refine it again makes no sense, imo
You have very fine gold powder ready to be washed clean by acids, so why melt the impurities back in the gold, where it is much harder to reach?
Martijn
Well-known member
looking at your pictures; My very first advice for you to do: go buy some plastic gloves! Dirt cheap and life altering! (you will live longer)
Martijn
Well-known member
How many hot water washes did you do on this powder?
@Emryst
If I were you, I'd listen to the feedback you've already received from some of the most knowledgeable professionals on this forum...
Just a piece of advice in all fairness.
Or call the bomb squad...
Good looking out. I am trying to get better at remembering to put gloves on. I'm 53 and I have always used my hand from wood working to car repair. And stopping to put gloves on was never a thing. But yes it is a behavior I need to be much more mindful of. Appreciate you cheif.
I seem to remember adding a small amount of sulphuric acid during digestion, looks like a dirty drop, and to much SMB,
Ash it and start again, keep testing, nearly there.
